- 您现在的位置：买卖IC网 > Sheet目录299 > 71M6545-IGT/F (Maxim Integrated)IC ENERGY METERING
71M6545/71M6545H Data Sheet
Table 14: Port Registers (DIO0-14)
SFR
Name
SFR
Address
D7
D6
D5
D4
D3
D2
D1
D0
P0
P1
P2
P3
80
90
A0
B0
DIO_DIR[3:0]
DIO_DIR[7:4]
DIO_DIR[11:8]
DIO_DIR[14:12]
DIO[3:0]
DIO[7:4]
DIO[11:8]
DIO[14:11]
All DIO ports on the chip are bi-directional. Each of them consists of a latch (SFR P0 to P3 ), an output
driver and an input buffer, therefore the MPU can output or read data through any of these ports. Even if
a DIO pin is configured as an output, the state of the pin can still be read by the MPU, for example when
counting pulses issued via DIO pins that are under CE control.
At power-up DIO0-14 are configured as outputs, but the pins are in a high-impedance state
because PORT_E=0 (I/O RAM 0x270C[5]) . Host firmware should first configure DIO0-14 to the
desired state, then set PORT_E=1 to enable the function.
Clock Stretching ( CKCON[2:0], SFR 0x8E )
The CKCON[2:0] field defines the stretch memory cycles that are used for MOVX instructions when
accessing external peripherals. The practical value of this register for the 71M6545/H is to guarantee
access to XRAM between CE, MPU, and SPI.
Table 15 shows how the signals of the External Memory Interface change when stretch values are set
from 0 to 7. The widths of the signals are counted in MPU clock cycles. The post-reset state of the
CKCON[2:0] field (001), which is shown in bold in the table, performs the MOVX instructions with a
stretch value equal to 1.
Table 15: Stretch Memory Cycle Width
CKCON[2:0]
Stretch
Value
Read Signal Width
memaddr memrd
Write Signal Width
memaddr memwr
000
001
010
011
100
101
110
111
0
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
9
1
1
2
3
4
5
6
7
2.4.6
Instruction Set
All instructions of the generic 8051 microcontroller are supported. A complete list of the instruction set
and of the associated op-codes is contained in the 71M654x Software User’s Guide (SUG) .
2.4.7
UARTs
The 71M6545/H includes a UART (UART0) that can be programmed to communicate with a variety of
AMR modules and other external devices.
The UART is a dedicated 2-wire serial interface, which can communicate with an external host processor at
up to 38,400 bits/s (with MPU clock = 1.2288 MHz). The operation of the RX and TX UART0 pins is as
follows:
36
v2
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
720-10007-00300
CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025
CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300
CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300
CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881
8 POS T/P SHLD 4 GR ASSY
7250B
PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200
CBL DSUB HD 15FEMAL-15MALE 2.0M
73304-111
MJ HOR ESMT 8/8 H/O T&R
相关代理商/技术参数
71M6545-IGTR/F
功能描述:计量片上系统 - SoC Metrology Proc. (3P 64K Flsh .1%)
RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6545T-IGT/F
制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube
71M6545T-IGTR/F
制造商:Maxim Integrated Products 功能描述:3-PHASE AFE, 32KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6601
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IF
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL/F
功能描述:模数转换器 - ADC Isolated Sensor IC
RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
71M6601-ILF
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring